Laptop Starts Up Again After Shutdown Dell Xps 15

Contents

• i Why Windows x Restarts After Shutdown?
• two What To Do When Computer Restarts After Shutdown?
  • 2.1 Solution 1: Perform A Clean Kicking
  • 2.ii Solution 2: Enter Safety Kick
  • 2.3 Solution 3: Disable Automatic Restart Later Organisation Failure
  • 2.iv Solution iv: Turn Off Fast Startup
  • ii.5 Solution 5: Force Shutdown Using Command Prompt
• iii Wrapping Upwardly

If your Windows 10 restarts after shutdown, and then you are non the only i facing this result. This event has been around for many years and yet hasn't been fixed entirely by Microsoft.

The reckoner restarting subsequently shutdown can be very abrasive for users. Because of this, many users only plough off the power after the computer shuts down so that it doesn't have time to restart once more. Only that's not a solution to the issue and anyway information technology won't work for laptop users.

In this article, we have discussed what can trigger this issue and besides some troubleshooting methods that can gear up this trouble.

Also, cheque out this article on what to practice when Windows update gets stuck.

Why Windows x Restarts After Shutdown?

If the Windows 10 won't shut down and just restarts over again, then it seems that the computer is crashing at the moment of the shutdown, which is why it restarts dorsum. In that location is a feature in Windows 10 that will restart the computer if it crashes , which is what this issue probably looks like.

As the Windows x crashes at the moment of the shutdown, the user doesn't observe the crash and think the reckoner just restarts after shutdown. The computer tin crash due to both hardware and software failures.

Some users, withal, have also reported that the Fast startup feature is responsible for this issue. Now, that the causes of this issue are known it'southward time to troubleshoot.

What To Do When Computer Restarts Subsequently Shutdown?

Read and execute the following solutions advisedly and this issue should get fixed.

Solution 1: Perform A Make clean Boot

Equally mentioned higher up, the figurer probably crashes during the shutdown, which causes it to restart again. In this scenario, performing a make clean kicking should disable all the unessential apps and services, which can atomic number 82 to the crash.

To perform a clean boot, follow the steps given below:

1. Press the Windows + R keys to open the Run utility.
2. Type msconfig and press Enter to open the System Configuration dialog.

3. Select the Services tab and check the Hibernate all Microsoft services box.
4. Click on the Disable all option to disable all the unnecessary services.

5. Now, click on the Startup tab and then click on the Open Task Manager option.
   The Task Manager will open on your screen.
6. Select the Startup tab and disable all the apps in the list.
   Correct-click on the app and select the Disable option.

7. Finally, restart your calculator to boot in the clean kick surround.

Later the figurer restarts, close downwardly once again. If the estimator shuts down properly, then ane of the services or apps you simply disabled is the culprit. However, if still the PC won't shut downward and only restarts, then try the next solution.

Solution two: Enter Condom Boot

If performing a clean boot didn't work, and so try entering the Prophylactic Kicking. In safety boot all the unnecessary drivers are disabled. So, if the issue is acquired by faulty drivers, then the issue should go resolved.

To enter rubber boot, follow the steps given below:

1. Open the Organization Configuration dialog again.
2. Select the Kicking tab.
3. Check the Safe boot box and so select the Minimal choice.

4. Finally, click on Utilise and OK and so restart the computer.

Shutdown the computer after it boots in desktop and then check if the PC shuts down without restarting. If the PC shuts down properly, then faulty drivers are the culprit for this outcome.

Solution three: Disable Automatic Restart After Organisation Failure

When the system crashes, the estimator restarts on its own. Disabling this feature should stop the figurer from restarting if the system crashes during the shutdown. Sometimes the computer restarts after sleep too, this issue virtually likely occurs due to organisation failure and so disabling automated restart should solve this problem also.

To disable automated restart after a arrangement failure, follow the steps given below:

1. Open the Run utility again.
2. Type sysdm.cpl and press Enter to open the System Backdrop.

3. Select the Advanced tab and click on the Settings pick in the Startup and Recovery

4. In the System Failure department, uncheck the Automatically restart box.

5. Finally, click on OK to save the changes.

At present, shut down your reckoner. If yet Windows ten won't shut down and just restarts, and then almost likely the outcome is not caused by system failure during the shutdown. Effort the adjacent solution and run across if it works.

Solution 4: Turn Off Fast Startup

If the above solutions didn't piece of work, then try disabling the Fast startup feature. Many users have reported that disabling the Fast startup feature fixed this event for them. If the computer is non restarting because of system failure, then Fast startup seems the almost likely culprit.

The Fast startup feature was introduced as a way to decrease the kick fourth dimension taken past Windows. Nevertheless, the feature has been reported for instigating various errors and bugs over the years.

To disable Fast startup, follow the steps given below:

1. Type Power & Slumber settings in the Windows search bar and select the top pick.
2. Select the Boosted ability settings in the Related settings department.
3. Click on the Cull what the power buttons practice option.

4. Select the Change settings that are currently unavailable choice, which would allow you modify the Shutdown settings.
5. Uncheck the Plow on fast startup (recommended) box and click on the Salvage changes pick.

After disabling the Fast startup, check if even so Windows ten restarts after shutdown.

Solution 5: Force Shutdown Using Command Prompt

If disabling Fast startup likewise didn't work, then try executing a force shutdown using the Control Prompt. To execute Force shutdown, follow the steps given below:

1. Type cmd in the Run utility and press the Ctrl + Shift + Enter keys.
   An elevated Command Prompt will open on your screen.
2. Type shutdown /s /f /t 0 and printing Enter.

At present the computer should shut down.

Wrapping Upward

 So, there you have it. Now y'all know what to do if Windows 10 restarts after shutdown again. If the result is caused due to system failure or crash, then Solution three should work. Don't forget to share your views and opinions on this commodity in the comment section beneath.

deeringmosume.blogspot.com

Source: https://digicruncher.com/windows-10-restarts-after-shutdown/

Share this post